THIN WALLED CRYOGENIC MACHINING ON INCONEL OR AEROSPACE MATERIALS
Abstract
Conventional liquids and lubricants are widely used in machining processes throughout the world. However, this cutting liquid is the source of many environmental pollution problems. In order to reduce or eliminate the effect produced by cutting fluids, it is necessary to switch to a continuous machining technique such as using small amounts of cutting fluid, liquid nitrogen, vegetable oil or compressed air as a cooling lubrication medium. Cryogenic coolant is found to be more efficient, economical, cost-effective and environmentally friendly when compared to the conventional coolant, especially in mass production. In machining difficult-to-cut materials such as thin walled materials for the aerospace industry, cooling applications are needed. Ni-based superalloy, Inconel is a material for aerospace applications because of its high durability to wear and material that is resistant to oxidation and corrosion at high temperatures. This paper presents a review and explanation of thin wall machining using cryogenic cooling systems on inconel or aerospace materials.
Full Text:
PDFReferences
REFERENCES
X. Jiang, W. Lu, and Z. Zhang, “An approach for improving the machining efficiency and quality of aerospace curved thin-walled parts during five-axis NC machining,” Int. J. Adv. Manuf. Technol., vol. 97, no. 5–8, pp. 2477–2488, 2018.
L. Jiang et al., “Research on bending forming method of large diameter-thickness ratio thin-walled tubes for aerospace,” Int. J. Adv. Manuf. Technol., vol. 102, no. 9–12, pp. 3037–3049, 2019.
J. SHI, Q. SONG, Z. LIU, and X. AI, “A novel stability prediction approach for thin-walled component milling considering material removing process,” Chinese J. Aeronaut., vol. 30, no. 5, pp. 1789–1798, 2017.
A. U. H. Mohsan, Z. Liu, and G. K. Padhy, “A review on the progress towards improvement in surface integrity of Inconel 718 under high pressure and flood cooling conditions,” Int. J. Adv. Manuf. Technol., vol. 91, no. 1–4, pp. 107–125, 2017.
Chetan, S. Ghosh, and P. Venkateswara Rao, “Application of sustainable techniques in metal cutting for enhanced machinability: A review,” J. Clean. Prod., vol. 100, no. March, pp. 17–34, 2015.
I. S. Jawahir et al., “Cryogenic manufacturing processes,” CIRP Ann. - Manuf. Technol., vol. 65, no. 2, pp. 713–736, 2016.
B. Dilip Jerold and M. Pradeep Kumar, “Experimental investigation of turning AISI 1045 steel using cryogenic carbon dioxide as the cutting fluid,” J. Manuf. Process., vol. 13, no. 2, pp. 113–119, 2011.
Y. Kaynak and A. Gharibi, “Progressive Tool Wear in Cryogenic Machining: The Effect of Liquid Nitrogen and Carbon Dioxide,” J. Manuf. Mater. Process., vol. 2, no. 2, p. 31, 2018.
A. Shokrani and S. T. Newman, “A new cutting tool design for cryogenic machining of Ti-6Al-4V titanium alloy,” Materials (Basel)., vol. 12, no. 3, pp. 1–14, 2019.
O. Pereira, A. Rodríguez, J. Barreiro, A. I. Fernández-Abia, and L. N. L. de Lacalle, “Nozzle design for combined use of MQL and cryogenic gas in machining,” Int. J. Precis. Eng. Manuf. - Green Technol., vol. 4, no. 1, pp. 87–95, 2017.
W. H. Pereira and S. Delijaicov, “Surface integrity of INCONEL 718 turned under cryogenic conditions at high cutting speeds,” Int. J. Adv. Manuf. Technol., pp. 2163–2177, 2019.
L. S. Ahmed and M. P. Kumar, “Cryogenic Drilling of Ti–6Al–4V Alloy Under Liquid Nitrogen Cooling,” Mater. Manuf. Process., vol. 31, no. September, pp. 951–959, 2015.
B. V. Ramanaiah, B. Manikanta, M. Ravi Sankar, M. Malhotra, and K. Gajrani, “Experimental Study of Deflection and Surface Roughness in Thin Wall Machining of Aluminum Alloy,” Mater. Today Proc., vol. 5, no. 2, pp. 3745–3754, 2018.
G. Bolar and S. N. Joshi, “Three-dimensional numerical modeling, simulation and experimental validation of milling of a thin-wall component,” Proc. Inst. Mech. Eng. Part B J. Eng. Manuf., vol. 231, no. 5, pp. 792–804, 2017.
S. Borojevic, D. Lukic, M. Miloševic, J. Vukman, and D. Kramar, “Optimization of process parameters for machining of Al 7075 thin-walled structures,” Adv. Prod. Eng. Manag., vol. 13, no. 2, pp. 125–135, 2018.
A. Isaev, V. Grechishnikov, P. Pivkin, K. Mihail, Y. Ilyuhin, and A. Vorotnikov, “Machining of Thin-walled Parts Produced by Additive Manufacturing Technologies,” Procedia CIRP, vol. 41, pp. 1023–1026, 2016.
E. O. Ezugwu, “Key improvements in the machining of difficult-to-cut aerospace superalloys,” Int. J. Mach. Tools Manuf., vol. 45, no. 12–13, pp. 1353–1367, 2005.
D. Umbrello, “Investigation of surface integrity in dry machining of Inconel 718,” Int. J. Adv. Manuf. Technol., vol. 69, no. 9–12, pp. 2183–2190, 2013.
F. Pusavec, H. Hamdi, J. Kopac, and I. S. Jawahir, “Surface integrity in cryogenic machining of nickel based alloy - Inconel 718,” J. Mater. Process. Technol., vol. 211, no. 4, pp. 773–783, 2011.
D. A. Stephenson, S. J. Skerlos, A. S. King, and S. D. Supekar, “Rough turning Inconel 750 with supercritical CO2-based minimum quantity lubrication,” J. Mater. Process. Technol., vol. 214, no. 3, pp. 673–680, 2014.
F. Pusavec et al., “Sustainable machining of high temperature Nickel alloy - Inconel 718: Part 1 - Predictive performance models,” J. Clean. Prod., vol. 81, pp. 255–269, 2014.
F. Pusavec et al., “Sustainable machining of high temperature Nickel alloy - Inconel 718: Part 2 - Chip breakability and optimization,” J. Clean. Prod., vol. 87, no. 1, pp. 941–952, 2015.
L. M. Maiyar, R. Ramanujam, K. Venkatesan, and J. Jerald, “Optimization of machining parameters for end milling of Inconel 718 super alloy using Taguchi based grey relational analysis,” Procedia Eng., vol. 64, pp. 1276–1282, 2013.
Refbacks
- There are currently no refbacks.
Indexing Journal JMSE : 
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.