• https://theoejwilson.com/
  • santuy4d
  • mariatogel
  • santuy4d
  • garuda slot
  • garudaslot
  • https://edujournals.net/
  • nadimtogel
  • https://mitrasehatjurnal.com/
  • slot gacor hari ini
  • g200m
  • 55kbet
  • slot gacor
  • garudaslot
  • link slot gacor
  • https://perpustakaan.stpreinha.ac.id/mahasiswa/
  • https://www.lml.stpreinha.ac.id/lab/
  • https://cursosvirtuales.icip.edu.pe/nice/
    • CNC PROGRAM AND PROGRAMMING OF CNC MACHINE | Fatriyana | Journal of Mechanical Science and Engineering

    CNC PROGRAM AND PROGRAMMING OF CNC MACHINE

    Maya Fatriyana

    Abstract


    CNC Programming (Computer Numerical Control Programming) is the art of programming CNC machines to make parts. An NC Program consists of a sequence of instructions that control the motion and automatic sequences of an NC Machine. In general sense, the term NC programming refers to the creation of control data for machining work-pieces on NC and CNC machines. The development of CNC systems has progressed as a result of the rapidly improving capabilities, coupled with falling prices, of small computers, a combination that makes the standard computer an attractive component of NC systems. NC programming has a decisive influence on the cost effectiveness and profitability of NC manufacturing. The selection of a programming system is essentially guided by the need for software that is suitable for the application at hand, readily available, and as universally applicable as possible.

    Keywords


    CNC Program, CNC Machine, Manufacturing System

    Full Text:

    PDF

    References


    M. Kovacic, M. Brezocnik, I. Pahole, J. Balic, and B. Kecelj,

    “Evolutionary Programming of CNC Machines,” J. Mater. Process.

    Technol., vol. 164–165, pp. 1379–1387, 2005, doi:

    1016/j.jmatprotec.2005.02.047.

    Z. Mu, G. Zhang, Y. Ran, S. Zhang, and J. Li, “A Reliability Statistical

    Evaluation Method of CNC Machine Tools Considering the Mission

    and Load Profile,” IEEE Access, vol. 7, pp. 115594–115602, 2019,

    doi: 10.1109/access.2019.2935622.

    S. N. Grigoriev, A. A. Kutin, and V. V. Pirogov, “Advanced Method of

    NC Programming for 5-Axis Machining,” Procedia CIRP, vol. 1, no. 1,

    pp. 102–107, 2012, doi: 10.1016/j.procir.2012.04.016.

    R. Wdowik, M. Magdziak, R. M. C. Ratnayake, and C. Borsellino,

    “Application of Process Parameters in Planning and Technological

    Documentation: CNC Machine Tools and CMMs Programming

    Perspective,” Procedia CIRP, vol. 78, pp. 43–48, 2018, doi:

    1016/j.procir.2018.09.054.

    J. Duda and J. Pobozniak, “The Architecture of Intelligent System for

    CNC Machine Tool Programming,” Procedia Manuf., vol. 11, no. June,

    pp. 501–508, 2017, doi: 10.1016/j.promfg.2017.07.143.

    T. Schroeder and M. Hoffmann, “Flexible Automatic Converting of NC

    Programs . A Cross-Compiler for Structured Text,” vol. 7543, no.

    May, 2016, doi: 10.1080/00207540500455841.

    R. Licari, E. Lo Valvo, and M. Piacentini, “Part Program Automatic

    Check for Three Axis CNC Machines,” J. Mater. Process. Technol., vol.

    , no. 3, pp. 290–293, 2001, doi: 10.1016/S0924-

    (00)00812-8.

    Y. Koren, “Computer-Based Machine-Tool Control,” no. March, pp.

    –83, 1977.


    Refbacks

    • There are currently no refbacks.


    Indexing Journal JMSE :
    google scholar    google scholar



    Creative Commons License
    This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.


    Flag Counter


    View My Stats