• https://theoejwilson.com/
  • santuy4d
  • mariatogel
  • santuy4d
  • garuda slot
  • garudaslot
  • https://edujournals.net/
  • nadimtogel
  • https://mitrasehatjurnal.com/
  • slot gacor hari ini
  • g200m
  • https://perpustakaan.stpreinha.ac.id/mahasiswa/
  • https://www.lml.stpreinha.ac.id/lab/
  • https://cursosvirtuales.icip.edu.pe/nice/
  • slot resmi
    • EFFECT OF CLEARANCE ON THE HEIGHT OF (BURR) ON ARM REAR BRAKE TYPE 45P AT PT. XYZ KARAWANG | Sumardi | Jurnal Pendidikan Teknik Mesin

    EFFECT OF CLEARANCE ON THE HEIGHT OF (BURR) ON ARM REAR BRAKE TYPE 45P AT PT. XYZ KARAWANG

    Sumardi Sumardi, Kardiman Kardiman, Farradina Choria Suci

    Abstract


    Arm rear break is one component of vehicle spare parts found on motorcycles. This component is made using a forming process, where one of the parameters that affects the failure is the clearance value. Therefore, the purpose of this study was to determine the effect of clearance on the burr height of the 45P Arm Rear Break. The arm rear break is made of sheet metal plate material with a thickness of 2.6 mm through the forming process and variations in clearance numbers of 4%, 5% and 6%. For the punching process, a 12 mm diameter punch knife was used. The result of this research is that the highest bar value is produced by 6% clearance of 0.29 mm, then 5% clearance of 0.23 mm and 4% clearance of 0.17 mm.

     

    Keywords : Sheet metal, forming, arm rear brake, clearance, burr



    Full Text:

    PDF

    References


    Ahmad Hasnan S. (2012). Mengenal Proses Deep Drawing. Jakarta,

    Ir.,MT. Hery Sonawan. (2014). Perancangan Elemen Mesin. Bandung: ALFABETA,CV.

    PT. Misumi Indonesia. (2018). Misumi Standar Components For Press Die.: Misumi Corporation.

    Suryadi VY. (2013). Pengaruh ketebalan material dan clearance progressive dies terhadap kualitas produk ring M7.

    Groover M.P. (2002). Fundamental Of Modern Manufacturing, Material, Processes and System, Second Edition.: Jhon Wiley & Sons, Inc, 2002.

    S. Kalpakjian. (1995). Manufacturing Engineering and Technology, Third Edition.: Addison-wesley.

    Gusniar Nugraha Iwan. (2018). AnalisisHasil Proses Broaching Pada Lubang Arm Rear Break Sepeda Motor. Universitas Singaperbangsa Karawang.

    Ides Bagus Rizqan M. (2017). Analisa Burr dengan Variasi Ketebalan Lembaran Alumunium Pada Proses Double Punch.

    PT. Ciptaunggul Karya Abadi. (2015). Handbook Proses Pembuatan Arm Rear Break.: Karawang.

    Muhammad Akhlis R. (2014). Analisa Proses Blanking dengan Simple Press Tool. Politeknik Negeri Malang




    DOI: https://doi.org/10.36706/jptm.v8i2.15318

    Refbacks

    • There are currently no refbacks.


     

    Jurnal Pendidikan Teknik Mesin
    Program Pendidikan Teknik Mesin
    Fakultas Keguruan dan Ilmu Pendidikan
    Universitas Sriwijaya, Palembang, Indonesia

    Diindeks dalam:

          

    View JPTM Stats

    Creative Commons License
    This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.