EFFECT OF  CUTTING PARAMETERS ON LOW CARBON STEEL SURFACE ROUGHNESS IN THE CONVENTIONAL TURNING PROCESS

Fahrizal Fahrizal; Priyono Priyono; Sealtial Mau; Anastasia De Delia Dos Santos

doi:10.36706/jptm.v9i1.17256

EFFECT OF CUTTING PARAMETERS ON LOW CARBON STEEL SURFACE ROUGHNESS IN THE CONVENTIONAL TURNING PROCESS

Fahrizal Fahrizal, Priyono Priyono, Sealtial Mau, Anastasia De Delia Dos Santos

Abstract

In the turning process, the surface roughness is affected by cutting parameters such as cutting speed, depth of cut, feed rate, and so on. However, there is not much information about the relationship or interaction between cutting parameters and the resulting surface roughness. This study aimed to examine the effect of cutting parameters on the surface roughness value of low carbon steel. This research was conducted experimentally using a conventional lathe with a HSS insert without the use of cutting fluids. It was concluded that the cutting parameters had a significant effect on the surface roughness. The lowest surface roughness value was obtained at 280 rpm spindle speed, 0.5 mm depth of cut and 0.2 mm/rev. feed rate with a roughness value of 2.968 µm. The contribution of each parameter to the surface roughness were 42.2% of spindle speed, 10% of depth of cut and 20.3% of feed rate respectively.

Full Text:

PDF

References

Fauzi, A., & Sumbodo, W. (2021). Pengaruh Parameter Pemakanan terhadap Kekasaran Perkukaan ST 40 pada Mesin Bubut CNC. Jurnal Dinamika Vokasional Teknik Mesin. Vol. 6, No. 1.

Gupta, H.N., Gupta, R.C., & Mittal, A. (2009). Manufacturing Process (2nd ed.) New Delhi: New Age International.

Gultom, P.I., & Kiswandono. (2020). Pengaruh Kecepatan Potong, Kecepatan Pemakanan dan Sudut Potong Utama terhadap Kekasaran Permukaan pada Proses Bubut Medium Carbon Steel’, Jurnal Flywheel. Vol. 11, No. 2.

Pawanr, S., Garg, G.K., & Routroy S. (2019). Multi-objective optimization of machining parameters to minimize surface roughness and power consumtion using TOPSIS. Procedia 7th CIRP Global Web Conference, 86. (pp. 116-120).

Sudjana (1985). Disain dan Analisis Eksperimen (edisi kedua). Bandung: Tarsito.

Stolk, J., & Kros C. (1993). Elemen Mesin Elemen Konstruksi dari Bangunan (edisi ke 21). Jakarta: Penerbit Erlangga.

Schey, J.A. (2009). Proses Manufaktur (edisi ketiga). Yogyakarta: Penerbit Andi.

Schonmetz, A., & Gruber, K. (2013). Pengetahuan Bahan dalam Pengerjaan Logam (edisi revisi). Bandung: Penerbit Angkasa.

Schonmetz, A., Sinnl, P., & Heuberger, J. (2013). Pegerjaan Logam dengan Mesin (edisi revisi). Bandung: Penerbit Angkasa.

Sugiyono, 2015. Metode Penelitian Pendidikan: Pendekatan Kuantitatif, Kualitatif, dan R&D. Bandung: Alfabeta.

Sunengsih N., Winarni, S., & Amzainaa, T.G. (2017). Kajian Terhadap Metode Taguchi-TOPSIS pada Optimasi Multirespon. Makalah prosiding pada Seminar Nasional Statistika VI FMIPA 2017 di Universitas Padjajaran, Bandung.

Siswanto, B., & Sunyoto. (2018). Pengaruh Kecepatan dan Kedalaman Potong pada Proses Pembubutan Konvensional terhadap Kekasaran Permukaan Lubang. Jurnal Dinamika Vokasional Teknik Mesin. Vol. 3, No. 2.

Salam, R., & Sunarto. (2020). Pengaruh Kecepatan Potong (Vc) terhadap Kekasaran Permukaan pada Pembubutan Kering Baja ASTM A 29 Menggunakan Pahat Karbida Berlapis Titanium Aluminium Nitrida (TiAIN). Jurnal Polimesin. Vol. 18, No, 1.

Yufrizal A., Indrawan, E., Helmi, N., Aziz, A., & Putra, Y.A. (2019). Pengaruh Sudut Potong dan Kecepatan Putaran Spindel terhadap Kekasaran Permukaan pada Proses Bubut Mild Steel ST 37. Jurnal Inovasi Vokasional dan Teknologi. Vol. 19, No. 2.

DOI: https://doi.org/10.36706/jptm.v9i1.17256

Refbacks

There are currently no refbacks.

Jurnal Pendidikan Teknik Mesin
Program Pendidikan Teknik Mesin
Fakultas Keguruan dan Ilmu Pendidikan
Universitas Sriwijaya, Palembang, Indonesia

Diindeks dalam:

View JPTM Stats

This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.

Username
Password
Remember me